Blade Set New

Over 4,000 Stokes per Minute-Silent Running Motor-Break Resistant Housing Uses all A5 Blades-10 pc comb set-Works on all brands of clippers. Includes sizes: 1/16, 1/8, , 3/8, , 5/8, , 7/8, 1, 1. Oster Turbo A5 2-Speed Clipper with a FREE 10pc comb set. Important Safeguards Commercial Clipper When using an electrical appliance, basic precautions should always be followed, including the following: Read all instructions before using this appliance. Do not reach for an appliance that has fallen into water. Do not use while bathing or in a shower. Do not place or store appliance where it can fall or be pulled into a tub or sink. Do not place in or drop into water or other liquids. Always unplug this appliance from the electrical outlet immediately after using. Unplug this appliance before cleaning, putting on or taking off parts. Warning To reduce the risk of burns, fire, electric shock, or injury to persons: 1. An appliance should never be left unattended when it is plugged in. Close supervision is necessary when this appliance is used by, on, or near children or invalids. Use this appliance only for its intended use as described in this manual. Do not use attachments not recommended by the manufacture. Never operate this appliance if it has a damaged cord, or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water. Return the appliance to a service center for examinations and repair. Keep cord away from heated surfaces. Never operate the appliance when air opening are blocked or while on a soft surface (such as bed or couch). Never drop or insert any object into opening. Do not use outdoors or operate where aerosol spray products are being used or where oxygen is being administered. Do not use this appliance with a damaged or broken comb or blade, as cut or scratched skin may occur. To disconnect, move all controls to OFF, then remove plug from outlet. Do not wrap cord around unit when storing. Continuous stress on the cord can damage cord insulation and result in a shock hazard. Avoid contact with moving blades. Avoid tangling or kinking the cord while clipping. Should the cord become tangled or kinked, stop clipping and straighten cord. This appliance is for clipping and trimming purpose only. Keep the appliance dry. The intended continuous operating time is 20 minutes. During use, do not place or leave the appliance where it is expected to : 1 Subject to damage by animal, or exposed to weather 18. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilitys, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person should be supervised to ensure that they do not play with the appliance. Directions and Dosage Instructions. Do not tamper with clipper Operate on voltage specified on clipper Do not use this clipper until you have read these operating instructions Operating the Unit Always apply on to two drops of the provided blade lubricant or other Oster approved lubricants to the blades before use. Cutting efficiency may drop and the blades and motor may be damaged if hair is dirty or hair styling agents have been applied. Always ensure that hair is clean before using the clipper. Turn the clipper on using the On-Off switch located on the top of the unit and use the clipper. Turn the clipper off when finished using. Cover the blades with the provided blade guard to protect the blades. Unplug unit after use and store properly. The product is for commercial use. Keep cord straight while clipping. If cord becomes kinked or tangled, stop clipping and straighten it. Do not wrap cord around the clipper when storing. This can damage the cord insulation. Always take care not to tangle the cord while using or storing the clipper. We recommended storing the clipper and cord in the original carton when not in use. Greasing Over-greasing can cause leakage and reduce the operating efficiency of the clipper. Check once a month by removing metal nameplate. Then remove nylon lever, metal link, and gear. Insert grease tube nozzle into hole on top of gear post. (Note: If grease does not come through, clean holes). Do not fill cavity with grease. Now replace link & gear and add very little grease to teeth of gear and linkage. Use only Oster Electric clipper grease. This grease is required in double insulated clippers because of its insulative properties. Caution: Add very little grease and only when necessary. Carbon Brushes Brushes must be inspected and replaced periodically to insure maximum motor performance and life expectancy. Unplug the clipper for the power outlet to prevent and electric shock when inspecting or replacing brushes. To remove a brush on models with a slotted brush cap, unscrew the cap (a dime is an excellent tool for this) and remove nylon insulator cap. Remove the brass cap by applying slight pressure to the side of the cap with a fingernail in a picking fashion. Remove the brush and spring assembly and compare the length of the round and square sections of the brush. When the square section has been reduced to the length of the round section, the brush must be replaced to prevent possible damage to the motor armature. Always replace the brushes as a set of 2 brushes even though only one may be at or below the required length. When reinstalling the brush spring-pressing down to seat the brass cap into the brush tube. Replace the slotted out cap and screw down tightly to prevent loosening. Use Oster Brushes Avoid substitutes. Brushes used in electric motors are carefully selected for size and grade to obtain maximum, trouble free performance. When ordering carbon brushes, specify model number and voltage of clipper. Blade sharpening Oster cutting blades are if individual hollow-ground design, hardened to extend cutting life. As with any cutting instrument, the cutting edges will become dull with usage. Increasing blade tension to force dull blades to cut can cause the clipper to heat and reduce motor life, and further shorten blade life. When the cutting blades no longer cut smooth and clean, sharpening is necessary. When sharpening blades becomes necessary, send blades to an Authorized Service Center where approved methods, equipment and proper knowledge are used to restore the original hollow-ground design and best cutting ability. Sharpening blades by flat grinding or any method contrary to the design and construction of Oster cutting blades is not recommended. Removing or Replacing Blades To Remove Important! Stop motor; lift blade away from clipper and slide of tongue. To replace Turn motor on; insert blade on tongue fully then snap blade into place. Lubricating the Blades A light film of oil should be maintained on the surface of the cutting blades. Oiling the blades frequently while in use will help keep the blades cleaner. Clean blades cut better. To clean blades, dip the teeth into Oster Blade Wash cleaner with the clipper running. Do not immerse the clipper. Remove from the mixture and, while holding the clipper with the blade end down, wipe the blades dry with a clean, dry cloth. See products for details. Storage and Disposal Requirements. To store unit, coil and place in original carton. Keep in a dry place. Pattern Design and Style. The item “Oster Turbo A5 2-Speed Clipper with 10pc Comb Set Free Blade Value of $35″ is in sale since Wednesday, October 7, 2020. This item is in the category “Pet Supplies\Dog Supplies\Grooming\Scissors & Fur Clippers”. The seller is “vetmedicinesforless” and is located in Fairbury, Nebraska. This item can be shipped to United States.

• Brand: Oster
• Type: Pet Supplies
• Custom Bundle: No
• MPN: 31161294
• Modified Item: No